CDCVF2505PWRG4 OverviewTape & Reel (TR)-method packaging is used for clock ICs. The 8-TSSOP (0.173, 4.40mm Width) package contains this clock generator. This clock generator ic can sustain a maximum temperature of 260 during reflowing. It contains 8 terminations that can be found in frequency synthesizer. This electronic frequency generator requires a voltage of 3.3V. The input of this clock generator is designed to be LVTTL. To access the full performance of the electronic component, 1 circuits are implemented. Thanks to the Surface Mount, this electric component can be conveniently installed on the panel. This clock generator would require a maximum supply voltage of 3.6V. For safety reasons, this frequency synthesizer should have a voltage supply above 3V. As far as the supply voltage is concerned, clock PLL can be used with 3V~3.6V. Based on the test statistics, an ambient temperature of -40°C~85°C should be set. This electronic component is usually classified as a PLL Clock Driver component. The clock-generating IC is a 8-bit device designed specifically for microprocessors. You can find related electrical components to the base part number CDCVF2505. It is possible to connect to the frequency generators via 8 pins. There is a maximum supply voltage of 3.3V that clock generator can handle. 4 signal outputs enable clock PLL to magnify output frequency as high as possible. At a frequency of 200MHz, frequency generator is capable of achieving high efficiency. In terms of load capacitance, analog clock generator is capable of delivering 25pF. This clock generator ic is ideally suited to the TR package.
CDCVF2505PWRG4 FeaturesAvailable in the 8-TSSOP (0.173, 4.40mm Width)
Supply voltage of 3.3V
Operating supply voltage of 3.3V
Load capacitance of 25pF
CDCVF2505PWRG4 ApplicationsThere are a lot of Texas Instruments
CDCVF2505PWRG4 Clock Generators applications.
Automatic test equipment
Wide area power system
Digital circuits
Wireless base station for LTE, LTE-advanced
Picocells, femtocells and small cells
Sampling clocks for ADC and DAC
1 Gigabit Ethernet
10 Gigabit Ethernet
FPGA and processor clocks
Line cards used in telephone exchange
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Factory Lead Time | 6 Weeks |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 8 |
| Weight | 39.008944mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | PLL Clock Driver |
| Packing Method | TR |
| Voltage - Supply | 3V~3.6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Frequency | 200MHz |
| Base Part Number | CDCVF2505 |
| Pin Count | 8 |
| Number of Outputs | 4 |
| Operating Supply Voltage | 3.3V |
| Supply Voltage-Max (Vsup) | 3.6V |
| Supply Voltage-Min (Vsup) | 3V |
| Number of Circuits | 1 |
| Load Capacitance | 25pF |
| Nominal Supply Current | 5μA |
| Output Characteristics | 3-STATE WITH SERIES RESISTOR |
| Input | LVTTL |
| Ratio - Input:Output | 1:5 |
| PLL | Yes with Bypass |
| Differential - Input:Output | No/No |
| Height | 1.2mm |
| Length | 3mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
+8613715157867